View APA2069J-TU_554977.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

APA2069
Stereo 2.6W Audio Power Amplifier (with DC_Volume Control)
Features
* * * * * * * * * * *
Low Operating Current with 9mA Improved Depop Circuitry to Eliminate Turn-on and Turn-off Transients in Outputs High PSRR 32 Steps Volume Adjustable by DC Voltage with Hysteresis 2.6W per Channel Output Power into 4 Load at 5V,BTL Mode Two Output Modes Allowable with BTL and SE Modes Selected by SE/BTL pin Low Current Consumption in Shutdown Mode (1A) Short Circuit Protection Thermal shutdown protection and over current protection circuitry Power DIP-16 Package Lead Free Available (RoHS Compliant)
General Description
APA2069 is a monolithic integrated circuit, which provides precise DC volume control, and a stereo bridged audio power amplifiers capable of producing 2.6W (1.8W) into 4 with less than 10% (1.0%)THD+N. The attenuator range of the volume control in APA2069 is from 20dB (DC_Vol=0V) to -80dB (DC_Vol=3.54V) with 32 steps. The advantage of internal gain setting can be less components and PCB area. Both of the depop circuitry and the thermal shutdown protection circuitry are integrated in APA2069, that reduce pops and clicks noise during power up or shutdown mode operation. It also improves the power off pop noise and protects the chip from being destroyed by over temperature and short current failure. To simplify the audio system design, APA2069 combines a stereo bridge-tied loads (BTL) mode for speaker drive and a stereo single-end (SE) mode for headphone drive into a single chip, where both modes are easily switched by the SE/BTL input control pin signal.
Applications
* * NoteBook PC LCD Monitor or TV
ANPEC reserves the right to make changes to improve reliability or manufacturability without notice, and advise customers to obtain the latest version of relevant information to verify before placing orders. Copyright (c) ANPEC Electronics Corp. Rev. A.1 - Aug., 2005 1 www.anpec.com.tw
APA2069
Ordering and Marking Information
APA2069
Lead Free Code Handling Code Temp. Range Package Code APA2069 J : APA2069 XXXXX Package Code J : PDIP-16 Operating Ambient Temp. Range I : - 40 to 85 C Handling Code TU : Tube Lead Free Code L : Lead Free Device Blank : Original Device XXXXX - Date Code
Note: ANPEC lead-free products contain molding compounds/die attach materials and 100% matte tin plate termination finish; which are fully compliant with RoHS and compatible with both SnPb and lead-free soldiering operations. ANPEC lead-free products meet or exceed the lead-free requirements of IPC/JEDEC J STD-020C for MSL classification at lead-free peak reflow temperature.
Block Diagram
LOUT+
LINVolume Control
LOUT-
RINBYPASS
BYPASS ROUT+
VOLUME
ROUTSE/BTL
SE/BTL Power and Depop circuit
VDD
SHUTDOWN
Shutdow n ckt
GND
APA2069_Block
Copyright (c) ANPEC Electronics Corp. Rev. A.1 - Aug., 2005
2
www.anpec.com.tw
APA2069
Absolute Maximum Ratings
(Over operating free-air temperature range unless otherwise noted.)
Symbol VDD VIN TA TJ TSTG TS VESD PD
Notes: 1.APA2069 integrated internal thermal shutdown protection when junction temperature ramp up to 150C 2.Human body model: C=100pF, R=1500, 3 positives pulse plus 3 negative pulses 3.Machine model: C=200pF, L=0.5F, 3 positive pulses plus 3 negative pulses
Parameter Supply Voltage Range Input Voltage Range, SE/BTL, SHUTDOWN Operating Ambient Temperature Range Maximum Junction Temperature Storage Temperature Range Soldering Temperature,10 seconds Electrostatic Discharge Power Dissipation
Rating -0.3 to 6 -0.3 to VDD+0.3 -40 to 85 Intermal Limited* -65 to +150 260 2 -3000 to 3000* 3 -200 to 200* Intermal Limited
1
Unit V V C C C C V
Recommended Operating Conditions
Min. Supply Voltage, VDD High level threshold voltage, VIH Low level threshold voltage, VIL Common mode input voltage, VICM SHUTDOWN SE/BTL SHUTDOWN SE/BTL VDD-1.0 4.5 2 4 1.0 3 Max. 5.5 Unit V V
V V
Thermal Characteristics
Symbol RTHJA Parameter Thermal Resistance from Junction to Ambient in Free Air DIP-16 45 C/W Value Unit
Copyright (c) ANPEC Electronics Corp. Rev. A.1 - Aug., 2005
3
www.anpec.com.tw
APA2069
Electrical Characteristics
VDD=5V, -20CSymbol VDD IDD Supply Current Supply Current in Shutdown Mode High input Current Low Input Current Output Differential Voltage Parameter Supply Voltage SE/BTL=0V SE/BTL=5V SE/BTL=0V SHUTDOWN=0V 1 900 900 5 Test Condition Min. 4.5 9 4 APA2069 Unit Typ. Max. 5.5 20 mA 10 A nA nA mV V
ISD IIH IIL VOS
Operating Characteristics, BTL mode. VDD=5V,TA=25C,RL=4, Gain=2V/V (unless otherwise noted)
Symbol Parameter Test Condition THD=10%, RL=3, Fin=1kHz THD=10%, RL=4, Fin=1kHz PO THD=10%, RL=8, Fin=1kHz Maximum Output Power THD=1%, RL=3, Fin=1kHz THD=1%, RL=4, Fin=1kHz THD=0.5%, RL=8, Fin=1kHz THD+N Total Harmonic Distortion Plus Noise PSRR Power Ripple Rejection Ratio Xtalk S/N Channel Separation Signal to Noise Ratio PO=1.2W, RL=4, Fin=1kHz PO=0.9W, RL=8, Fin=1kHz VIN=0.1Vrms, RL=8, CB=1F, Fin=120Hz CB=1F, RL=8, Fin=1kHz PO=1.1W, RL=8, A_wieght 60 90 95 dB dB dB 1 Min. APA2069 Unit Typ. Max. 2.9 2.6 1.6 2.4 1.8 1.3 0.07 0.08 % W
Operating Characteristics, SE mode. VDD=5V,TA=25C, Gain=1V/V (unless otherwise noted)
Symbol Parameter Test Condition THD=10%, RL=16, Fin=1kHz PO THD=10%, RL=32, Fin=1kHz Maximum Output Power THD=1%, RL=16, Fin=1kHz THD=1%, RL=32, Fin=1kHz
Copyright (c) ANPEC Electronics Corp. Rev. A.1 - Aug., 2005 4
APA2069 Unit Min. Typ. Max. 220 120 160 95
www.anpec.com.tw
mW
APA2069
Electrical Characteristics (Cont.)
Operating Characteristics, SE mode. VDD=5V,TA=25C, Gain=1V/V (unless otherwise noted)
Symbol Parameter Test Condition PO=125mW, RL=16, Fin=1kHz PO=65mW, RL=32, Fin=1kHz VIN=0.1Vrms, RL=8, CB=1F, Fin=120Hz CB=1F, RL=32, Fin=1kHz PO=75mW, SE, RL=32, A_wieght 60 60 100 dB dB dB APA2069 Unit Min. Typ. Max. 0.09 0.09 %
THD+N Total Harmonic Distortion Plus Noise PSRR Power Ripple Rejection Ratio Xtalk S/N Channel Separation Signal to Noise Ratio
Pin Description
SHUTDOWN BYPASS RINGND 1 2 3 4 16 15 14 13 12 11 10 9 ROUTVDD ROUT+ GND GND LOUT+ VDD LOUT-
APA2069
GND 5 LIN- 6 VOLUME 7 SE/BTL 8
Pin Function Description
Pin No. 1 2 3 4,5,12,13 6 7 8 9 10,15 11 14 16 Name SHUTDOWN BYPASS RINGND LINVOLUME SE/BTL LOUTVDD LOUT+ ROUT+ ROUTConfig I I I I I I O O O O Function Description It will be into shutdown mode when pull low. ISD = 1A Bias voltage generator Right channel input terminal Ground connection, Connected to thermal pad. Left channel input terminal Input signal for internal volume gain setting. Output mode control input, high for SE output mode and low for BTL mode. Left channel positive output in BTL mode and SE mode. Supply voltage Left channel negative output in BTL mode and high impedance in SE mode. Right channel negative output in BTL mode and high impedance in SE mode. Right channel positive output in BTL mode and SE mode.
5 www.anpec.com.tw
Copyright (c) ANPEC Electronics Corp. Rev. A.1 - Aug., 2005
APA2069
Typical Application Circuit
VDD 100 F
0.1 F V DD
GND LOUT+
L-CH Input
1 F
220 F LINVolume Control
4 LOUT-
1k SE/BTL Signal
Control Pin Ring
R-Ch Input
1 F
RINBYPASS
BYPASS ROUT+ 2.2 F 220 F 4
Sleeve Tip Headphone Jack 1k
V DD
VDD 50k VOLUME
100k
100k
SE/BTL
SE/BTL
ROUT-
Shutdow n Signal
SHUTDOWN
Shutdown ckt
A2069_AppCkt
Volume Control Table_BTL Mode
Supply Voltage Vdd=5V
Gain(dB) 20 18 16 14 12 10 8 6 4 2 0 -2 -4 -6 -8 High(V) 0.12 0.23 0.34 0.46 0.57 0.69 0.80 0.91 1.03 1.14 1.25 1.37 1.48 1.59 1.71 Low(V) 0.00 0.17 0.28 0.39 0.51 0.62 0.73 0.84 0.96 1.07 1.18 1.29 1.41 1.52 1.63 Hysteresis(mV) 52 51 50 49 47 46 45 44 43 41 40 39 38 37 Recommended Voltage(V) 0 0.20 0.31 0.43 0.54 0.65 0.77 0.88 0.99 1.10 1.22 1.33 1.44 1.56 1.67
Copyright (c) ANPEC Electronics Corp. Rev. A.1 - Aug., 2005
6
www.anpec.com.tw
APA2069
Volume Control Table_BTL Mode (Cont.)
Supply Voltage Vdd=5V
Gain(dB) -10 -12 -14 -16 -18 -20 -22 -24 -26 -28 -30 -32 -34 -36 -38 -40 -80 High(V) 1.82 1.93 2.05 2.16 2.28 2.39 2.50 2.62 2.73 2.84 2.96 3.07 3.18 3.30 3.41 3.52 5.00 Low(V) 1.74 1.85 1.97 2.08 2.19 2.30 2.42 2.53 2.64 2.75 2.87 2.98 3.09 3.20 3.32 3.43 3.54 Hysteresis(mV) 35 34 33 32 30 29 28 27 26 24 23 22 21 20 18 17 16 Recommended Voltage(V) 1.78 1.89 2.01 2.12 2.23 2.35 2.46 2.57 2.69 2.80 2.91 3.02 3.14 3.25 3.36 3.48 5
Typical Characteristics
THD+N vs. Output Power
10
THD+N vs. Output Power
10
VDD = 5V Av =20dB f = 1KHz RL = 8 BTL RL = 4
VDD = 5V Av =14dB f = 1KHz SE
THD+N (%)
THD+N (%)
1
RL = 3
1
RL = 32
RL = 16
0.1
0.1
0.01 0 0.5 1 1.5 2 2.5 3 3.5
0.01 0 40m 80m 120m 160m 200m 240m
Output Power (W)
Output Power (W)
Copyright (c) ANPEC Electronics Corp. Rev. A.1 - Aug., 2005
7
www.anpec.com.tw
APA2069
Typical Characteristics (Cont.)
THD+N vs. Output Power
10
10
THD+N vs. Output Power
VDD = 5V Av =20dB RL =3 BTL
VDD = 5V F =1KHz RL =3 BTL
THD+N (%)
1
THD+N (%)
1
f = 20KHz
Av = 20dB
0.1
f = 20Hz f = 1KHz
Av = 6dB
0.1
0.01 0 0.5 1 1.5 2 2.5 3 3.5
0.05 10m
100m
1
5
Output Power (W)
Output Power (W)
THD+N vs. Frequency
10
THD+N vs. Frequency
10
VDD = 5V RL =3 Po = 1.8W BTL
VDD = 5V Av = 6dB RL =3 BTL
1
THD+N (%)
0.1
Av = 20dB
THD+N (%)
1
0.1
Po = 0.9W
Av = 6dB
Po = 1.8W
0.01 20 100 1k 10k 20k
0.01 20
100
1k
10k
20k
Frequency (Hz)
Frequency (Hz)
Copyright (c) ANPEC Electronics Corp. Rev. A.1 - Aug., 2005
8
www.anpec.com.tw
APA2069
Typical Characteristics (Cont.)
THD+N vs. Output Power
10
10
THD+N vs. Output Power
VDD = 5V F =1KHz RL =4 BTL
VDD = 5V Av =20dB RL =4 BTL F = 20KHz
1
THD+N (%)
1
THD+N (%)
F = 20Hz
Av = 20dB
0.1
0.1
F = 1KHz
Av = 6dB
0.01 0 0.5 1 1.5 2 2.5 3 3.5
0.01 10m 100m 1 5
Output Power (W)
Output Power (W)
THD+N vs. Frequency
10
THD+N vs. Frequency
10
VDD = 5V RL=4 Po=1.5W BTL
VDD = 5V Av= 6dB RL=4 BTL
1
THD+N (%)
THD+N (%)
1
0.1
Av = 6dB
0.1
Po = 0.8W
Po = 1.5W
Av = 20dB
0.01 20
100
1k
10k
20k
0.01 20
100
1k
10k
20k
Frequency (Hz)
Frequency (Hz)
Copyright (c) ANPEC Electronics Corp. Rev. A.1 - Aug., 2005
9
www.anpec.com.tw
APA2069
Typical Characteristics (Cont.)
THD+N vs. Output Power
10
10
THD+N vs. Output Power
VDD = 5V F= 1KHz RL=8 BTL
VDD = 5V Av = 20dB RL=8 BTL
THD+N (%)
THD+N (%)
1
1
F = 20KHz F = 20Hz
Av = 6dB
0.1
0.1
Av = 20dB
F = 1KHz
0.01
0
0.5
1
1.5
2
2.5
3
3.5
0.01 10m
100m
1
5
Output Power (W)
Output Power (W)
THD+N vs. Frequency
10
10
THD+N vs. Frequency
VDD=5V RL=8 Po=0.9W BTL
1
VDD = 5V Av = 6dB RL=8 BTL
THD+N (%)
Po = 0.5W
0.1
THD+N (%)
1
Av = 6dB
0.1
Po = 0.9W
Av = 20dB
0.01 20
0.01
100
1k
10k
20k
20
100
1k
10k 20k
Frequency (Hz)
Frequency (Hz)
Copyright (c) ANPEC Electronics Corp. Rev. A.1 - Aug., 2005
10
www.anpec.com.tw
APA2069
Typical Characteristics (Cont.)
THD+N vs. Output Power
10
10
THD+N vs. Output Power
VDD=5V F=1KHz RL=16 SE
VDD=5V Av=14dB RL=16 Co=1000f SE
1
THD+N (%)
1
THD+N (%)
F = 20KHz
F = 20Hz
Av = 0dB
0.1
0.1
Av = 14dB
F = 1KHz
0.01 0 40m 80m 120m 160m 200m 240m
0.01 10m 50m 100m 200m 300m
Output Power (W)
Output Power (W)
THD+N vs. Frequency
10
10
THD+N vs. Frequency
VDD=5V RL=16 Po=125mW Co=1000f SE
VDD=5V Av=0dB RL=16 Co=1000f SE
1
THD+N (%)
THD+N (%)
1
Av = 0dB
0.1
Po = 125mW
0.1
Av = 14dB
Po = 60mW
0.01 20
100
1k
10k
20k
0.01 20
100
1k
10k
20k
Frequency (Hz)
Frequency (Hz)
Copyright (c) ANPEC Electronics Corp. Rev. A.1 - Aug., 2005
11
www.anpec.com.tw
APA2069
Typical Characteristics (Cont.)
THD+N vs. Output Power
10
THD+N vs. Output Power
10
V DD=5V F=1KHz RL=32 SE
VDD=5V Av=14dB RL=32 Co=1000 f SE
1
THD+N (%)
1
THD+N (%)
F = 20KHz
0.1
F = 20Hz
Av = 0dB
0.1
Av = 14dB
F = 1KHz
0.01 0 40m 80m 120m 160m 200m 240m
0.01 10m
50m
100m
200m 300m
Output Power (W)
Output Power (W)
THD+N vs. Frequency
10
THD+N vs. Frequency
10
V DD=5V RL=32 Po=65mW Co=1000f SE
VDD=5V Av=14dB RL=32 Co=1000f SE
THD+N (%)
Av = 0dB
0.1
THD+N (%)
1
1
Po = 30mW
0.1
Av = 14dB
Po = 65mW
0.01 20 100 1k 10k 20k
0.01 20
100
1k
10k
20k
Frequency (Hz)
Frequency (Hz)
Copyright (c) ANPEC Electronics Corp. Rev. A.1 - Aug., 2005
12
www.anpec.com.tw
APA2069
Typical Characteristics (Cont.)
Frequency Response
+20 +330
+20
Frequency Response
+330
Amplitude( 20dB)
+320 +16 +310
+16
Amplitude( 20dB)
+320
Phase( 20dB)
+310
Phase(Degress)
Phase(Degress)
Amplitude(dB)
+12
Phase( 20dB)
+300
Amplitude(dB)
+12
+300
+190 +8
+8
+190
Phase( 6dB)
+180
Phase( 6dB)
+180 +4
+4
+0 10
VDD=5V RL=4 Po=0.8W BTL
100
Amplitude( 6dB)
+170
+160 1k 10k 100k 200k
+0 10
VDD=5V RL=8 Po=0.5W BTL
Amplitude( 6dB)
+170
100
1k
10k
+160 100k 200k
Frequency (Hz)
Frequency (Hz)
Frequency Response
+14 +300
Frequency Response
+14 +220
Amplitude(14dB)
+10
Amplitude(14dB)
+280
+10
+210
Phase(Degress)
Phase(Degress)
Amplitude(dB)
+260 +6
Phase(14dB)
+6 +200
Amplitude(dB)
Phase(14dB)
+240 +220
+2
Amplitude(0dB)
+2
+200 +180
Amplitude(0dB)
-2
+190
-2
-6
VDD=5V RL=16 Co=1000f Po=60mW SE
100
Phase(0dB)
+160
-6
+140 +120 100k 200k
VDD=5V RL=32 Co=1000f Po=30mW SE
100 1k 10k
Phase(0dB)
+180
+170 +165 100k 200k
-10 20
1k
10k
-10 20
Frequency (Hz)
Frequency (Hz)
Copyright (c) ANPEC Electronics Corp. Rev. A.1 - Aug., 2005
13
www.anpec.com.tw
APA2069
Typical Characteristics (Cont.)
Crosstalk vs. Frequency
+0
+0 -10 -20 -30
Crosstalk vs. Frequency
VDD=5V -10 RL=8 -20 Po=0.9 W BTL
-30
VDD=5V RL=4 Po=1.5 W BTL
Crosstalk(dB)
-50 -60 -70 -80
Crosstalk(dB)
-40
-40 -50 -60 -70 -80 -90 -100
Right to Left
Right to Left
-90 -100 -110 -120 20 100
Left to Right
Left to Right
1k 10k 20k
-110 -120
20
100
1k
10k 20k
Frequency (Hz)
Frequency (Hz)
Crosstalk vs. Frequency
+0 -10 -20 -30
Crosstalk vs. Frequency
+0 -10 -20 -30
VDD=5V RL=16 Co=1000f Po=125mW SE
VDD=5V RL=32 Co=1000f Po=65mW SE
Crosstalk(dB)
Crosstalk(dB)
-40 -50 -60 -70 -80 -90 -100 20
-40 -50
Right to Left Left to Right
Right to Left
-60
Left to Right
-70 -80 -90 -100
100
1k
10k
20k
20
100
1k
10k
20k
Frequency (Hz)
Frequency (Hz)
Copyright (c) ANPEC Electronics Corp. Rev. A.1 - Aug., 2005
14
www.anpec.com.tw
APA2069
Typical Characteristics (Cont.)
Output Noise Voltage vs. Frequency
100u
100u
Output Noise Voltage vs. Frequency
Output Noise Voltage(V)
Output Noise Voltage(V)
Filter BW<22KHz
20u
20u
Filter BW<22KHz
A-Weight
10u
10u
A-Weight
VDD=5V Av=6dB RL=4 BTL
1u 20 100 1k 10k 20k
1u 20
VDD=5V Av=0dB RL=32 SE
100 1k 10k 20k
Frequency (Hz)
Frequency (Hz)
PSRR vs. Frequency
+0 -10 -20 -30
+0
PSRR vs. Frequency
VDD=5V RL=4 Vin=200mV Av=20dB BTL
-10 -20 -30
VDD=5V RL=32 Vin=200mV Av=14dB SE
PSRR(dB)
-40 -50 -60 -70 -80 -90 -100 20 100 1k 10k 20k
PSRR(dB)
-40 -50 -60 -70 -80 -90 -100 20
100
1k
10k
20k
Frequency (Hz)
Frequency (Hz)
Copyright (c) ANPEC Electronics Corp. Rev. A.1 - Aug., 2005
15
www.anpec.com.tw
APA2069
Typical Characteristics (Cont.)
Shutdown Attenuation vs. Frequency
+0 -10
Gain vs. DC volume Voltage
20
Shutdown Attenuation(dB)
-20 -30 -40 -50 -60 -70 -80 -90
VDD=5V RL=8 Vin=1V RMS Av=6dB BTL
10 0 -10 Dow n
Gain (dB)
-20 -30 -40 -50 -60
Up
-100 -110 -120 20
-70 -80 0.0
VDD=5V No Load BTL
0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0
100
1k
10k
20k
Frequency (Hz)
DC volume (V)
Supply Current vs. Supply Voltage
10.0
Power Dissipation vs. Output Power
2.0 1.8
No Load BTL
9.0
RL=3
1.6
Supply Current(mA)
8.0
Power Dissipation(W)
1.4 1.2 1.0 0.8 0.6 0.4 0.2 0.0 0.00
RL=4
7.0
6.0
5.0
RL=8
SE
4.0
3.0
VDD=5V THD<1% BTL
0.50 1.00 1.50 2.00 2.50
2.0 3.0
3.5
4.0
4.5
5.0
5.5
Supply Voltage(V)
Output Power(W)
Copyright (c) ANPEC Electronics Corp. Rev. A.1 - Aug., 2005
16
www.anpec.com.tw
APA2069
Typical Characteristics (Cont.)
Power Dissipation vs. Output Power
200
RL=8
180 160
Power Dissipation(W)
140 120 100 80
RL=16
RL=32
60 40 20 0 0 50 100 150 200 250
VDD=5V THD<1% SE
Output Power(W)
Application Descriptions
BTL Operation The APA2069 output stage (power amplifier) has two pairs of operational amplifiers internally, allowed for different amplifier configurations. The power amplifier' OP1 gain is setting by internal s unity-gain and input audio signal is come from internal volume control amplifier, while the second amplifier OP2 is internally fixed in a unity-gain, inverting configuration. Figure 1 shows that the output of OP1 is connected to the input to OP2, which results in the output signals of with both amplifiers with identical in magnitude, but out of phase 180. Consequently, the differential gain for each channel is 2 x (Gain of SE mode). By driving the load differentially through outputs OUT+
RL OUTVbias Circuit OP2
OUT+
Volume Control amplifier output signal
OP1
and OUT-, an amplifier configuration commonly referred to as bridged mode is established. BTL mode operation is different from the classical single-ended SE amplifier configuration where one side of its load is connected to ground. A BTL amplifier design has a few distinct advantages
17 www.anpec.com.tw
Figure 1: APA2069 internal configuration (each channel)
Copyright (c) ANPEC Electronics Corp. Rev. A.1 - Aug., 2005
APA2069
Application Descriptions (Cont.)
BTL Operation (Cont.) over the SE configuration, as it provides differentialdrive to the load, thus doubling the output swing for aspecified supply voltage. Four times the output power is possible as compared toa SE amplifier under the same conditions. A BTL configuration, such as the one used in APA2069, also creates a second advantage over SE amplifiers. Since the differential outputs, ROUT+, ROUT-, LOUT+, and LOUT-, are biased at half-supply, no need DC voltage exists across the load. This eliminates the need for an output coupling capacitor which is required in a single supply, SE configuration. Single-Ended Operation Consider the single-supply SE configuration shown Application Circuit. A coupling capacitor is required to block the DC offset voltage from reaching the load. These capacitors can be quite large (approximately 33F to 1000F) so they tend to be expensive, occupy valuable PCB area, and have the additional drawback of limiting low-frequency performance of the system (refer to the Output Coupling Capacitor).The rules described still hold with the addition of the following relationship: 1 << 1 1 (1) Cbypass x 125k RiCi RLCC Output SE/BTL Operation The ability of the APA2069 to easily switch between BTL and SE modes is one of its most important costs saving features. This feature eliminates the requirement for an additional headphone amplifier in applications where internal stereo speakers are driven in BTL mode but external headphone or speakers must be accommodated. Internal to the APA2069, two separate amplifiers drive OUT+ and OUT- (see Figure 1). The SE/BTL input
1k VDD 100k SE/BTL
Sleeve Control Pin Ring
controls the operation of the follower amplifier that drives LOUT- and ROUT-. * When SE/BTL is held low, the OP2 is turn on and the APA2069 is in the BTL mode. * When SE/BTL is held high, the OP2 is in a high output impedance state, which configures the APA2069 as SE driver from OUT+. IDD is reduced by approximately one-half in SE mode. Control of the SE/BTL input can be a logic-level TTL source or a resistor divider network or the stereo headphone jack with switch pin as shown in Application Circuit.
Tip
Headphone Jack
Figure 2: SE/BTL input selection by phonejack plug In Figure 2, input SE/BTL operates as follows : When the phonejack plug is inserted, the 1k resistor is disconnected and the SE/BTL input is pulled high and enables the SE mode. When the input goes high, the OUT- amplifier is shutdown causing the speaker to mute. The OUT+ amplifier then drives through the output capacitor (CO) into the headphone jack. When there is no headphone plugged into the system, the contact pin of the headphone jack is connnected from the signal pin, the voltage divider set up by resistors 100k and 1k.Resistor 1k then pulls low the SE/BTL pin, enabling the BTL function.
18 www.anpec.com.tw
Copyright (c) ANPEC Electronics Corp. Rev. A.1 - Aug., 2005
APA2069
Application Descriptions (Cont.)
Volume Control Function APA2069 has an internal stereo volume control whose setting is a function of the DC voltage applied to the VOLUME input pin. The APA2069 volume control consists of 32 steps that are individually selected by a variable DC voltage level on the VOLUME control pin. The range of the steps, controlled by the DC voltage, are from 20dB to -80dB. Each gain step corresponds to a specific input voltage range, as shown in table. To minimize the effect of noise on the volume control pin, which can affect the selected gain level, hysteresis and clock delay are implemented. The amount of hysteresis corresponds to half of the step width, as shown in volume control graph.
APA2069 DC Volume Control Curve (BTL)
20 10 0 -10 Forw ard
Input Resistance, Ri The gain for each audio input of the APA2069 is set by the internal resistors (Ri and Rf) of volume control amplifier in inverting configuration. RF (2) SE Gain = AV = Ri RF (3) BTL Gain = -2 x Ri BTL mode operation brings the factor of 2 in the gain equation due to the inverting amplifier mirroring the voltage swing across the load. For the varying gain setting, APA2069 generates each input resistance on figure 4. The input resistance will affect the low frequency performance of audio signal. The minmum input resistance is 10k when gain setting is 20dB and the resistance will ramp up when close loop gain below 20dB. The input resistance has wide variation (+/-10%) caused by process variation.
Ri(k) 120 100
Ri vs Gain(BTL)
Gain(dB)
-20 -30 -40 -50 -60 -70 -80 0.0
Backw ard
80 60 40 20
0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0
0 -40 -30 -20 -10 0 10 20 Gain(dB)
DC volume (V)
Figure 3: Gain setting vs VOLUME pin voltage For highest accuracy, the voltage shown in the ` recommended voltage'column of the table is used to select a desired gain. This recommended voltage is exactly halfway between the two nearest transitions. The gain levels are 2dB/step from 20dB to -40dB in BTL mode, and the last step at -80dB as mute mode.
Figure 4: Input resistance vs Gain setting Input Capacitor, Ci In the typical application an input capacitor, Ci, is required to allow the amplifier to bias the input signal to the proper DC level for optimum operation. In this
Copyright (c) ANPEC Electronics Corp. Rev. A.1 - Aug., 2005
19
www.anpec.com.tw
APA2069
Application Descriptions (Cont.)
Input Capacitor, Ci (Cont.) case, Ci and the minimum input impedance Ri (10k) form a high-pass filter with the corner frequency determined in the follow equation: 1 FC(highpass)= (4) 2x10kxCi The value of Ci is important to consider as it directly affects the low frequency performance of the circuit. Consider the example where Ri is 10k and the specification calls for a flat bass response down to 100Hz. Equation is reconfigured as follow : 1 Ci= (5) 2x10kxfC Consider to input resistance variation, the Ci is 0.16F so one would likely choose a value in the range A further consideration for this capacitor is the leakage path from the input source through the input network (Ri+Rf, Ci) to the load. This leakage current creates a DC offset voltage at the input to the amplifier that reduces useful headroom, especially in high gain applications. For this reason a low-leakage tantalum or ceramic capacitor is the best choice. When polarized capacitors are used, the positive side of the capacitor should face the amplifier input in most applications as the DC level there is held at VDD/2, which is likely higher that the source DC level. Please note that it is important to confirm the capacitor polarity in the application. Effective Bypass Capacitor, Cbypass As other power amplifiers, proper supply bypassing is critical for low noise performance and high power supply rejection. The capacitors located on both the bypass and power supply pins should be as close to the device as possible. The effect of a larger bypass capacitor will improve PSRR due to increased supply stability. Typical applications employ a 5V regulator with 1.0F and a 0.1F bypass capacitor as supply filtering. This
Copyright (c) ANPEC Electronics Corp. Rev. A.1 - Aug., 2005 20
does not eliminate the need for bypassing the supply nodes of the APA2069. The selection of bypass capacitors, especially Cbypass, is thus dependent upon desired PSRR requirements, click and pop performance. To avoid start-up pop noise occurred, the bypass voltage should rise slower than the input bias voltage and the relationship shown in equation (6) should be maintained. 1 1 << (6) Cbypass x 125k 100k x Ci The bypass capacitor is fed thru from a 125k resistor inside the amplifier and the 100k is maximum input resistance of (Ri+ Rf). Bypass capacitor, Cb, values of 3.3F to 10F ceramic or tantalum low-ESR capacitors are recommended for the best THD and noise performance. The bypass capacitance also effects to the start up time. It is determined in the following equation : Tstart up = 5 x (Cbypass x 125K) (7)
Output Coupling Capacitor, Cc In the typical single-supply SE configuration, an output coupling capacitor (Cc) is required to block the DC bias at the output of the amplifier thus preventing DC currents in the load. As with the input coupling capacitor, the output coupling capacitor and impedance of the load form a high-pass filter governed by equation. FC(highpass)= 1 2RLCC (8)
For example, a 330F capacitor with an 8 speaker would attenuate low frequencies below 60.6Hz. The main disadvantage, from a performance standpoint, is the load impedance is typically small, which drives the low-frequency corner higher degrading the bass response. Large values of CC are required to pass low frequencies into the load.
www.anpec.com.tw
APA2069
Application Descriptions (Cont.)
Power Supply Decoupling, Cs The APA2069 is a high-performance CMOS audio amplifier that requires adequate power supply decoupling to ensure the output total harmonic distortion (THD) is as low as possible. Power supply decoupling also prevents the oscillations causing by long lead length between the amplifier and the speaker. The optimum decoupling is achieved by using two different type capacitors that target on different type of noise on the power supply leads. For higher frequency transients, spikes, or digital hash on the line, a good low equivalent-series-resistance (ESR) ceramic capacitor, typically 0.1F placed as close as possible to the device VDD lead works best. For filtering lower-frequency noise signals, a large aluminum electrolytic capacitor of 10F or greater placed near the audio power amplifier is recommended. Optimizing Depop Circuitry Circuitry has been included in the APA2069 to minimize the amount of popping noise at power-up and when coming out of shutdown mode. Popping occurs whenever a voltage step is applied to the speaker. In order to eliminate clicks and pops, all capacitors must be fully discharged before turn-on. Rapid on/off switching of the device or the shutdown function will cause the click and pop circuitry. The value of Ci will also affect turn-on pops (Refer to Effective Bypass Capacitance). The bypass voltage ramp up should be slower than input bias voltage. Although the bypass pin current source cannot be modified, the size of Cbypass can be changed to alter the device turn-on time and the amount of clicks and pops. By increasing the value of Cbypass, turn-on pop can be reduced. However, the tradeoff for using a larger bypass capacitor is to increase the turn-on time for this device. There is a linear relationship between the size of Cbypass and the turn-on time. In a SE configuration, the output coupling capacitor, CC, is of particular concern. This capacitor discharges through the internal 10k resistors. Depending on the size of CC, the time constant can be relatively large. To reduce transients in SE mode, an external 1k resistor can be placed in parallel with the internal 10k resistor. The tradeoff for using this resistor is an increase in quiescent current. In the most cases, choosing a small value of Ci in the range of 0.33F to 1F, Cb being equal to 4.7F and an external 1k resistor should be placed in parallel with the internal 10k resistor should produce a virtually clickless and popless turn-on. A high gain amplifier intensifies the problem as the small delta in voltage is multiplied by the gain. So it is advantageous to use low-gain configurations. Shutdown Function In order to reduce power consumption while not in use, the APA2069 contains a shutdown pin to externally turn off the amplifier bias circuitry. This shutdown feature turns the amplifier off when a logic low is placed on the SHUTDOWN pin. The trigger point between a logic high and logic low level is typically 2.0V. It is best to switch between ground and the supply VDD to provide maximum device performance. By switching the SHUTDOWN pin to low, the amplifier enters a low-current state, I DD<1A. APA2069 is in shutdown mode. On normal operating, SHUTDOWN pin pull to high level to keeping the IC out of the shutdown mode. The SHUTDOWN pin should be tied to a definite voltage to av oid unwanted state changes. BTL Amplifier Efficiency An easy-to-use equation to calculate efficiency starts out as being equal to the ratio of power from the power
21 www.anpec.com.tw
Copyright (c) ANPEC Electronics Corp. Rev. A.1 - Aug., 2005
APA2069
Application Descriptions (Cont.)
BTL Amplifier Efficiency (Cont.) supply to the power delivered to the load. The following equations are the basis for calculating amplifier efficiency. PO (9) Efficiency = PSUP Where :
PO =
Note that in equation, VDD is in the denominator. This indicates that as VDD goes down, efficiency goes up. In other words, use the efficiency analysis to choose the correct supply voltage and speaker impedance for the application.
Po (W) Efficiency (%) IDD(A) VPP(V) PD (W) 0.25 31.25 47.62 66.67 78.13 0.16 0.21 0.30 0.32 2.00 2.83 4.00 4.47 0.55 0.55 0.5 0.35
V ORMS x V ORMS RL
=
VP x VP 2RL
VORMS =
VP 2
(10) (11)
0.50 1.00 1.25
PSUP = VDD x IDDAVG = VDD x 2VP RL Efficiency of a BTL configuration : PO VPxVP ) / (VDD x 2VP ) = VP =( 4VDD PSUP RL 2RL
**High peak voltages cause the THD to increase. (12) Table 1. Efficiency Vs Output Power in 5-V/8 BTL Systems Power Dissipation Whether the power amplifier is operated in BTL or SE modes, power dissipation is a major concern. In equation13 states the maximum power dissipation point for a SE mode operating at a given supply voltage and driving a specified load. VDD 2 (13) SE mode : PD,MAX= 2 2 RL In BTL mode operation, the output voltage swing is doubled as in SE mode. Thus the maximum power dissipation point for a BTL mode operating at the same given conditions is 4 times as in SE mode. 4VDD 2 (14) 22RL Since the APA2069 is a dual channel power amplifier, the maximum internal power dissipation is 2 times that both of equations depending on the mode of operation. Even with this substantial increase in power dissipation, the APA2069 does not require extra heatsink. The power dissipation from equation14, assuming a 5V-power supply and an 8 load, must not BTL mode : PD,MAX=
22 www.anpec.com.tw
Table 1 calculates efficiencies for four different output power levels. Note that the efficiency of the amplifier is quite low for lower power levels and rises sharply as power to the load is increased resulting in a nearly flat internal power dissipation over the normal operating range. Note that the efficiency of the amplifier is quite low for lower power levels and rises sharply as power to the load is increased resulting in a nearly flat internal power dissipation over the normal operating range. Note that the internal dissipation at full output power is less than in the half power range. Calculating the efficiency for a specific system is the key to proper power supply design. For a stereo 1W audio system with 8 loads and a 5V supply, the maximum draw on the power supply is almost 3W. A final point to remember about linear amplifiers (either SE or BTL) is how to manipulate the terms in the efficiency equation to utmost advantage when possible.
Copyright (c) ANPEC Electronics Corp. Rev. A.1 - Aug., 2005
APA2069
Application Descriptions (Cont.)
BTL Amplifier Efficiency (Cont.) be greater than the power dissipation that results from the equation15 : TJ,MAX - TA (15) PD,MAX= JA For PDIP16 package with thermal pad, the thermal resistance (JA) is equal to 45C/W. Since the maximum junction temperature (TJ,MAX) of APA2069 is 150C and the ambient temperature (TA) is defined by the power system design, the maximum power dissipation which the IC package is able to handle can be obtained from equation15. Once the power dissipation is greater than the maximum limit (PD,MAX), either the supply voltage (VDD) must be decreased, the load impedance (RL) must be increased or the ambient temperature should be reduced. Thermal Considerations Linear power amplifiers dissipate a significant amount of heat in the package under normal operating conditions. To calculate maximum ambient temperatures, first consideration is that the numbers from the Power Dissipation vs. Output Power graphs are per channel values, so the dissipation of the IC heat needs to be doubled for two-channel operation. Given JA, the maximum allowable junction temperature (TJMAX), and the total internal dissipation (PD), the maximum ambient temperature can be calculated with the following equation. The maximum recommended junction temperature for the APA2069 is 150C. The internal dissipation figures are taken from the Power Dissipation vs. Output Power graphs. TAMax = TJMax -JAPD 150 - 45(0.8*2) = 78C The APA2069 is designed with a thermal shutdown (16) protection that turns the device off when the junction temperature surpasses 150C to prevent damaging the IC.
Copyright (c) ANPEC Electronics Corp. Rev. A.1 - Aug., 2005
23
www.anpec.com.tw
APA2069
Packaging Information
PDIP-16 pin ( Reference JEDEC Registration MS-001)
D E c E1
eB
s Q1 A2 A1 A3 e b2
Millimeters Min. 0.38 3.17 2.92 0.36 1.14 0.76 0.20 18.632 7.605BSC 6.223 2.54BSC 8.492 1.397 0.58 3 9.506 1.651 0.84 8
24
A
b
b3
Inches
Dim A A1 A2 A3 b b2 b3 c D E E1 e eB Q1 s
Rev. A.1 - Aug., 2005
Max. 5.32 3.42 3.80 0.56 1.78 1.14 0.36 19.646 6.477
Min. 0.015 0.125 0.115 0.014 0.045 0.030 0.008 0.735 0.300BSC 0.245 0.100BSC 0.335 0.055 0.023 3
Max. 0.210 0.135 0.150 0.022 0.070 0.045 0.014 0.775 0.255 0.375 0.065 0.033 8
www.anpec.com.tw
Copyright (c) ANPEC Electronics Corp.
APA2069
Physical Specifications
Terminal Material Lead Solderability Solder-Plated Copper (Solder Material : 90/10 or 63/37 SnPb), 100%Sn Meets EIA Specification RSI86-91, ANSI/J-STD-002 Category 3.
Reflow Condition
(IR/Convection or VPR Reflow)
TP Ramp-up
tp Critical Zone T L to T P
Temperature
TL Tsmax
tL
Tsmin Ramp-down ts Preheat
25
t 25 C to Peak
Time
Classification Reflow Profiles
Profile Feature Average ramp-up rate (TL to TP) Preheat - Temperature Min (Tsmin) - Temperature Max (Tsmax) - Time (min to max) (ts) Time maintained above: - Temperature (T L) - Time (tL) Peak/Classificatioon Temperature (Tp) Time within 5C of actual Peak Temperature (tp) Ramp-down Rate Sn-Pb Eutectic Assembly 3C/second max. 100C 150C 60-120 seconds 183C 60-150 seconds See table 1 10-30 seconds Pb-Free Assembly 3C/second max. 150C 200C 60-180 seconds 217C 60-150 seconds See table 2 20-40 seconds
6C/second max. 6C/second max. 6 minutes max. 8 minutes max. Time 25C to Peak Temperature Notes: All temperatures refer to topside of the package .Measured on the body surface.
25 www.anpec.com.tw
Copyright (c) ANPEC Electronics Corp. Rev. A.1 - Aug., 2005
APA2069
Classification Reflow Profiles (Cont.)
Table 1. SnPb Entectic Process - Package Peak Reflow Temperature s Package Thickness Volume mm 3 Volume mm 3 <350 350 <2.5 mm 240 +0/-5C 225 +0/-5C 2.5 mm 225 +0/-5C 225 +0/-5C
Table 2. Pb-free Process - Package Classification Reflow Temperatures Package Thickness Volume mm 3 Volume mm 3 Volume mm 3 <350 350-2000 >2000 <1.6 mm 260 +0C* 260 +0C* 260 +0C* 1.6 mm - 2.5 mm 260 +0C* 250 +0C* 245 +0C* 2.5 mm 250 +0C* 245 +0C* 245 +0C* *Tolerance: The device manufacturer/supplier shall assure process compatibility up to and including the stated classification temperature (this means Peak reflow temperature +0C. For example 260C+0C) at the rated MSL level.
Reliability Test Program
Test item SOLDERABILITY HOLT PCT TST ESD Latch-Up Method MIL-STD-883D-2003 MIL-STD-883D-1005.7 JESD-22-B,A102 MIL-STD-883D-1011.9 MIL-STD-883D-3015.7 JESD 78 Description 245C, 5 SEC 1000 Hrs Bias @125C 168 Hrs, 100%RH, 121C -65C~150C, 200 Cycles VHBM > 2KV, VMM > 200V 10ms, 1 tr > 100mA
Customer Service
Anpec Electronics Corp. Head Office : 5F, No. 2 Li-Hsin Road, SBIP, Hsin-Chu, Taiwan, R.O.C. Tel : 886-3-5642000 Fax : 886-3-5642050 Taipei Branch : 7F, No. 137, Lane 235, Pac Chiao Rd., Hsin Tien City, Taipei Hsien, Taiwan, R. O. C. Tel : 886-2-89191368 Fax : 886-2-89191369
Copyright (c) ANPEC Electronics Corp. Rev. A.1 - Aug., 2005
26
www.anpec.com.tw

▲Up To Search▲

Price & Availability of APA2069J-TU

	To Download APA2069J-TU Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .